My pool light no longer works: causes and solutions

Circuit breaker, RCD, transformer, light bulb, water ingress: the causes of a pool light that no longer turns on, and which ones require an electrician.


Ma lumière de piscine ne fonctionne plus : causes et solutions

The short answer. Check these in order: the circuit breaker, the GFCI reset button, the switch, and then the transformer if you have one. These four points resolve the majority of cases and require no tools. If the power is getting there and the light remains off, it's the bulb, the LED, or water infiltration in the light fixture.

One rule above all: turn off the circuit breaker before touching the light fixture, and never turn on a pool light out of the water.

The four tool-free checks

1. The circuit breaker

Go to the panel. A tripped circuit breaker is not always obvious: some position themselves between the two positions. Push it completely to OFF, then back to ON.

If it trips again immediately, stop. A circuit breaker that trips every time indicates a fault, often water infiltration in the light fixture or cable. Leave it off and have it checked.

2. The GFCI

Pool circuits are protected by a ground fault circuit interrupter. It can be found at the panel, or on an outlet near the equipment, with its "Test" and "Reset" buttons.

A tripped GFCI cuts everything without anything appearing elsewhere. Press Reset.

If it trips again, do not force it. A GFCI exists precisely to detect a current leak into the water. It is doing its job, and this situation requires an electrician.

3. The switch and the timer

It seems obvious, and yet it is a frequent cause at the beginning of the season.

If your light is on a timer, check that the time is correct and that the jumpers are in place. A power outage shifts the clock, and the light then turns on at three in the morning.

If it is on a control system or an app, check that the program is active and that the module is communicating.

4. The transformer

If your installation is 12 V, it has a transformer, generally a metal box near the equipment.

Check that it is powered and that no indicator light shows a fault. Some models have an internal fuse. Replacing a fuse or opening the box involves 120 V and requires an electrician.

If the power is getting there and nothing turns on

The light source is finished

On an incandescent installation, this is the number one cause, and it is normal: a pool bulb is a wear part that is replaced periodically.

On an LED, a complete failure is rarer. An LED generally ages by losing intensity rather than turning off suddenly. An LED that no longer turns on at all points more towards its power supply or an infiltration.

If you need to replace it, it is the right time to assess the switch to LED: the light fixture is already out and the work is done. Our guide on LED conversion covers the issue.

There is water in the light fixture

A dry or cracked seal lets water in. You see it through the lens, or you notice persistent condensation.

This is the cause that explains most of the tripped circuit breakers. We cover the subject in detail in water in my pool light.

The cable is damaged

Rare, but real. A cable pinched during reassembly, gnawed by frost in a poorly drained conduit, or damaged during landscaping work.

The typical symptom is a GFCI that trips intermittently, often in damp weather. This is diagnosed with instruments, not by eye.

The diagnostic table

Symptom Probable cause What to do
Nothing anywhere, other equipment also affected Circuit breaker Reset at the panel
Only the light is dead GFCI or transformer Reset, then check the transformer
The circuit breaker trips every time Infiltration or cable fault Turn off and have checked
The GFCI trips in damp weather Current leak Electrician, without delay
Turns on at the wrong times Timer out of sync Set the time
Dim or flickering light LED at end of life, or power supply Inspect the light fixture
Water visible in the lens Defective seal Replace seal or light fixture
Frozen or erratic colors Programming sequence or module Restart the lighting sequence

The case of color lights that "no longer change"

Many color LEDs change programs through a sequence of power cuts: we turn off and on again in a certain rhythm to switch from one mode to another.

If your light remains frozen on a color, or if it changes at the wrong time, it is often an out-of-sync sequence, not a failure. Turn off the power for about thirty seconds, turn it back on, and restart the sequence indicated in the model's manual.

On an installation with multiple lights, they can also get out of sync with each other. The same maneuver generally gets them back in agreement.

What requires an electrician

In Quebec, electrical work is regulated. Three situations where we do not improvise:

A GFCI that trips again. It detects a current leak into the water. This is exactly the scenario that needs to be taken seriously.

Any work on the junction box, conduit, or transformer. This is permanent wiring.

A light fixture powered by 120 V. Replacement requires more precautions than a low-voltage model.

Replacing a light fixture in its niche, on a 12 V system, with the circuit breaker off, remains an accessible maintenance task.

Frequently asked questions

My pool light hasn't turned on since opening. Is that normal?
It is common. Start with the circuit breaker, the GFCI, and the timer. Winter often throws off clocks and trips protections.

The circuit breaker trips as soon as I turn on the light. What should I do?
Leave it off and have it checked. This is the classic symptom of water infiltration in the light fixture, and forcing the reset does not solve anything.

My LED light has become dimmer. Is it finished?
An LED loses intensity as it ages. If the brightness has significantly decreased without any other symptom, it is probably the normal end of life.

Can I change the bulb without emptying the pool?
Yes, in the vast majority of cases. The light fixture is removed from its niche and placed on the edge of the pool. See how to change a pool light.

My light works but remains stuck on a color.
Turn off the power for about thirty seconds, turn it back on, and restart the program change sequence of your model.


Our other guides on pool lighting

See our pool lights

A GFCI that trips or doubt about your installation? Our technicians travel to the Laurentians and the North Shore. Write to us or call 450-818-8200.



Discover certain products

1 of 4