Water in my pool light: what should I do
The short answer. Turn off the breaker before doing anything else. Water in a pool light creates a real electrical hazard, and it is the leading cause of tripped breakers and GFCI outlets. Only then should you determine whether it is simple condensation, which is sometimes harmless, or a clear leak, which will ruin the light if it is not corrected.
In almost all cases, the cause is the lens seal, and it needs to be replaced.
First, turn off the power
This is not a courtesy precaution.
A pool light with compromised sealing can leak current into the pool water. This is exactly what a GFCI is designed to detect, and that is why it exists.
If your GFCI or breaker trips and you see water in the light, do not reset it. Leave it off and have it inspected. Repeatedly resetting a circuit that detects a leak is exactly what you should not do.
No one should swim until the doubt is removed.
Condensation or a leak?
The two are not treated the same way.
Condensation appears as a light fog on the inside of the lens, sometimes with a few droplets. It appears and disappears with temperature fluctuations, typically in spring and fall. On some models, a light, occasional fog is acceptable according to the manufacturer.
A leak is obvious: free water at the bottom of the light, a visible water level, and sometimes whitish deposits or corrosion on the contacts. The lens remains fogged up permanently, even after several days.
The test that tells the difference: remove the light from its niche, set it on its side, and see if there is any moving water. Fogged-up air will clear in a few hours. Free water will not.
Why water gets in
The seal is dry or cracked. This is by far the most common cause. Rubber ages, hardens, loses its elasticity, and the seal fails. Quebec winters speed up the process.
The seal was lubricated with the wrong product. Vaseline and petroleum greases cause rubber to swell and then rot. Silicone is the only choice.
The lens is cracked. Sometimes this is not visible from the front. Look at it against the light, turning it over.
The light was tightened unevenly. Reassembling a light by tightening the screws out of order warps the lens and leaves a gap.
A grain of sand in the seal groove. That is enough. This is why the groove is cleaned before installing a new seal.
The cable is letting water in. This is rarer, but possible: a damaged cable can conduct water into the light through capillary action. In this case, replacing the seal will not solve the problem.
What to do
1. Turn off the breaker. Always do this first.
2. Remove the light from its niche. The complete procedure is in how to replace a pool light. It is generally not necessary to drain the pool.
3. Empty and dry. Open the light, empty the water, and let it dry completely. Completely means at least twenty-four hours in the open air, not twenty minutes in the sun.
4. Inspect. Look for corrosion on the contacts, whitish traces, a cracked lens, or a hardened seal.
5. Replace the seal. Always replace it, even if it looks fine. Clean the groove, install a new seal, and lubricate it with silicone.
6. Reassemble it properly. Tighten the screws in a crisscross pattern, evenly, without forcing them.
7. Test briefly before reinstalling, for just a few seconds, and never leave it out of the water any longer.
When the light is beyond repair
Three signs that a new seal will not be enough.
Corrosion on the electrical contacts. Once oxidation has set in, the connection becomes intermittent and reliability is compromised.
A cracked lens. On some models it can be replaced; on others, it cannot.
A leak that returns after the seal has been replaced. This points to the cable or a deformed housing.
In these cases, replacing the light is the right choice, and it is also the natural time to switch to LED if you have not already done so.
How to prevent it from happening again
Replace the seal every time the light is opened. It is a part that costs only a few dollars.
Lubricate with silicone only.
Clean the groove before installing a new seal.
Inspect it at least once a season. A quick look at the lens from the pool edge is enough to spot fog that is starting to build up.
Never leave a light on outside the water. Excessive heat warps the seal and fatigues the lens, setting the stage for a leak the following year.
Frequently asked questions
Is a little fog in my light serious?
A light, occasional fog that appears with temperature fluctuations and then disappears is acceptable on several models. Permanent fog or free water is not.
My GFCI trips and there is water in the light. What should I do?
Leave the circuit off, do not reset it, and have it inspected. The GFCI detects a current leak into the water and is doing exactly what it is designed to do.
Can I just empty the water and close it back up?
No. If you do not replace the seal, the water will return, and you will have only delayed the problem by one season.
Is water in the light dangerous to swimmers?
There is a risk, and that is why the power is turned off immediately. As long as the circuit is off, there is no electrical hazard.
How long should I let the light dry?
At least twenty-four hours in the open air, in a dry place. Residual moisture in a closed light causes exactly the condensation you are trying to eliminate.
Our other guides on pool lighting
- Switching your pool light to LED
- My pool light no longer works
- How to replace a pool light
- White or colored pool light: how to choose
Unsure about the safety of your installation? Turn off the breaker and call us. Our technicians serve the Laurentians and the North Shore. Write to us or call 450-818-8200.
