What salt level should be aimed for in a pool in Quebec?

The salt level depends on your system model, not a universal rule. How to measure it, when to add more, and why too much salt costs more than too little.


Quel taux de sel viser dans une piscine au Québec ?

The short answer. There is no universal rate: the target depends on your salt system model, and the difference between two brands is significant. Standard systems generally aim for around 3,000 ppm, while models designed for low salt levels operate with much less. Your manual is right, a general rule is wrong. What is universal, however, is that salt never evaporates, it is only lost through dilution, and an excess can only be removed by draining.

Why there is no single right answer

A salt chlorine generator converts dissolved salt into chlorine through electrolysis. The amount of salt it needs depends on the design of its cell.

Traditional systems need a relatively high concentration. Newer generations designed for low salt levels produce the same chlorine with much less, which reduces corrosion and makes the water taste less salty.

Searching for “the right salt level” without specifying the model therefore gives contradictory answers all over the internet. These are not mistakes, they are different models.

Find the target range in your device manual, or on the control box label. That is the only source that matters for your pool.

Too little, too much, and the comfort zone

Below target. Production drops or stops, and the system generally displays an alarm. Worse, a cell working in salt-deficient water has to work harder and wears out faster.

Above target. The system does not produce more chlorine because of it. The only effect is negative: the water tastes salty, corrosion accelerates on metal parts, ladders, steps, and certain equipment. At a significantly excessive level, several systems go into protection mode and stop producing.

The real problem with overdosing: it can only be corrected by diluting. There is no product that removes salt from water. You must drain part of the pool and refill it with fresh water. It is long, costly in water, and completely avoidable.

That is why salt is added gradually, never an extra bag “just to be sure.”

How to measure correctly

Do not rely solely on the system display. A scaled-up or worn cell displays false values, often lower than reality. People add salt for weeks because of a lying cell, and end up overdosing.

Use a test kit, salt-specific test strips, or have your water analyzed. We do it for free in store.

Measure at the right time. Wait until the added salt is completely dissolved and distributed, which generally takes several hours of filtration. Measuring too early gives a falsely low result and encourages adding more.

Measure away from the return jets, and not right after an addition.

When should you add more

Salt does not evaporate and is not consumed. The system recycles it in a loop: it converts it into chlorine, then the chlorine becomes salt again.

You therefore only lose it through dilution:

  • Opening the season. This is the most important time. A pool that spent the winter under rain and melting snow almost always restarts diluted.
  • Heavy rains. A rainy summer gradually lowers the level.
  • Backwashing. Each backwash flushes out salt water that you replace with fresh water.
  • Splashes and bather exits. Marginal, but real over a season.
  • Any addition of fresh water.

Test at opening, after a prolonged period of rain, and after any major refilling. The rest of the time, a monthly check is enough.

How to add salt correctly

Calculate before pouring. Start with the actual difference between your measurement and your model's target, and the volume of your pool. One extra bag is much harder to correct than one bag less.

Add gradually. Put in about three-quarters of what the calculation suggests, let it dissolve and circulate, measure again, then complete. It is slower and avoids draining.

Turn off the generator during dissolution. Run the pump alone, without production, until everything is dissolved.

Pour slowly into the deep end, with the pump running, and brush the bottom to help dissolution. Never pour salt directly into the skimmer: it passes through the plumbing without being dissolved and attacks the equipment in concentrated form.

Use salt designed for the pool. Pure salt, without anti-caking agents or additives, dissolves better and leaves no residue in the pool.

The most common mistakes

Adding salt because the system displays an alarm. First check with an independent test. The alarm often comes from a scaled-up cell, not a lack of salt.

Adding a bag by reflex at opening. The level may have dropped slightly. Measure.

Measuring too early after an addition. You read a falsely low level and add more.

Believing that more salt gives more chlorine. Beyond the target, performance does not increase. Only corrosion increases.

Frequently asked questions

What salt level for my pool?
The one indicated in your system manual. Standard models and low salt level models have very different targets, and following the wrong one damages the equipment.

Does salt evaporate?
No, never. You only lose it through dilution: rain, backwashing, splashes, addition of fresh water.

How to lower a salt level that is too high?
By draining part of the pool and refilling it with fresh water. No product removes salt from water. That is why we add gradually.

Does salt water taste like the sea?
No. The concentration of a salt pool is a fraction of that of sea water. If your water tastes distinctly salty, you are probably above your target.

Does salt damage the liner or concrete?
At the target concentration, no. Corrosion problems come from overdosing or chemically unbalanced water, not from salt itself.


Our other guides on salt systems

Free water analysis in store. Bring a sample, we will give you the actual level and the exact amount to add for your model. Write to us or call 450-818-8200.



Discover certain products

1 of 4